🪜 Stair Calculator PRO
Professional stair calculator — risers, treads, stringers, handrails, balusters, headroom, and IRC code compliance.
Dimension Diagram — updates as you type
Total rise sets the riser count; total run sets the footprint. The stringer is the hypotenuse.
1 Stair Type & Dimensions
L-Shaped Configuration
U-Shaped Configuration
Winder Configuration
Spiral Stair Configuration
2 IRC Code Checks (R403.1)
3 Materials & Configuration
4 Handrails & Balusters
5 Landing Size
6 Labour & Costing
Labour Cost
7 Project & Client Info
Results
Geometry
Material Breakdown
⚠️ Pre-Export Checklist
- Total rise verified on-site with laser level
- Landing dimensions confirmed at top and bottom
- Headroom clearance meets local code (min 6'8")
- Riser heights are uniform (max 3/8" variation)
- Stringer material and thickness specified
- Handrail height: 34–38 in above tread nosing
- Balusters spaced max 4 in apart (child-safe)
- Local code amendments reviewed (some jurisdictions stricter)
Professional Stair Building Guide
Show formulas, code references, and worked examples ▼
IRC Code Requirements (R403.1, R311.7)
- Max riser height: 7.75 inches (197 mm)
- Min tread depth: 10 inches (254 mm) — nosing adds 0.75" to 1.25"
- Rise + Run formula: (2 × Riser) + Tread = 25" to 27"
- Max variation between risers: 3/8 inch
- Min headroom: 6'8" (80 inches) clear — IRC R311.7.2
- Min stair width: 36 inches (residential), 44 inches (commercial)
- Handrail height: 34"–38" above tread nosing — IRC R311.7.8
- Baluster spacing: Max 4" openings — IRC R312.1
- Landing depth: Min 36" at top and bottom — IRC R311.7.5
- Max step count without intermediate landing: 14 risers
Stair Type Comparison
| Type | Space | Complexity | Cost |
|---|---|---|---|
| Straight | Most | Easy | Low |
| L-shaped | Medium | Medium | Medium |
| U-shaped | Compact | Medium | Medium-High |
| Winder | Compact | High | High |
| Spiral | Minimal | Very High | Highest |
Formulas
Number of Risers
= Total Rise ÷ Desired Rise Height
Round UP (never down — code requires uniform rise)
Actual Riser Height
= Total Rise ÷ Number of Risers
Must be ≤ 7.75 inches
Number of Treads
= Number of Risers − 1
Top riser lands on upper floor
Stringer Length
= √(Rise² + Run²) + Overhang
Pythagorean theorem + top overhang
Stair Angle
= arctan(Total Rise ÷ Total Run) × 180/π
Comfortable range: 30°–37.5°
Headroom
= Ceiling Height − (Tread Depth × sin(angle))
Must be ≥ 80 inches (6'8")
Baluster Count
= (Tread Depth × Num Treads) ÷ Spacing
Max 4" spacing per IRC R312.1
Handrail Length
= Stringer Length + Top/Bottom Extension
Both sides if width > 44"
Worked Example — Straight Stair
Inputs: Total Rise = 108 in (9 ft), Tread Depth = 10 in, Stair Width = 36 in, Ceiling = 120 in
- Risers needed: 108 ÷ 7.75 = 13.9 → 14 risers
- Actual riser height: 108 ÷ 14 = 7.71 in (PASS — under 7.75")
- Treads: 14 − 1 = 13 treads
- Check: (2 × 7.71) + 10 = 25.42 in (PASS — 25–27")
- Total run: 13 × 10 = 130 in
- Stringer: √(108² + 130²) = 168.8 in ≈ 14.1 ft
- Angle: arctan(108/130) = 39.8° (slightly steep — consider 9" run)
- Headroom: Using 10" run, 8 treads deep = 80 in vertically → 120 − 80 = 40 in (PASS)
- Handrail: 168.8 in + 12" top + 12" bottom = 192.8 in ≈ 16.1 ft (one side)
- Balusters: (10 × 13) ÷ 4 = 32.5 → 33 balusters
Stringer Count Guide
- 2 stringers: Standard for stairs ≤ 36" wide with solid treads
- 3 stringers: Recommended for stairs 36"–48" wide, or with composite/stone treads
- 4 stringers: Required for stairs > 48" wide, heavy traffic, or concrete treads
Common Mistakes to Avoid
- Measuring only the visible rise — include the top landing thickness
- Using different riser heights on the same flight (code violation — max 3/8" variation)
- Ignoring nosing projection in tread calculations
- Forgetting headroom clearance under intermediate landings
- Placing balusters more than 4" apart (child safety hazard — IRC R312.1)
- Setting handrails below 34" or above 38" — both are code violations
- Skip the landing at floor transitions — 36" minimum required
- Assuming spiral stairs meet residential code — check local amendments
Material Selection Guide
- Hardwood treads: Oak, maple — premium look, $15–30/lf, needs finishing
- Composite treads: Trex, Veranda — low maintenance, $20–40/lf, weather-resistant
- Concrete treads: Indoor/outdoor, $8–15/lf, heavy — needs 4 stringers
- Stone treads: Marble, granite, slate — luxury, $30–80/lf, very heavy
- Open risers: Modern look, improves light flow, must have ≤ 4" gaps
- Closed risers: Traditional, code-compliant everywhere, can be painted/stained
Tips
- Use a string line from finished floor to finished floor for accurate rise measurement
- Pre-cut stringers save time — mark riser and tread locations carefully with a framing square
- Treat stringers with preservative if they contact concrete or are in damp locations
- Always verify local code amendments — some jurisdictions are stricter than IRC baseline
- For winder stairs, the narrowest point of the tread at the walking line must be ≥ 10"
- Spiral stairs: headroom must be measured at the outer edge of the treads
- L-shaped and U-shaped stairs need an intermediate landing — minimum 36" × stair width
- Factor in finishing time: stain, paint, or seal each tread and riser before installation
Drag to rotate — Scroll to zoom
Связанные Калькуляторы
Frequently used together on the same project.
Client & Quote (prints on PDF & Excel)
Adjustments (applies to exports)
Contingency is added as a separate line on the exported cost summary. Waste % is printed as an advisory reminder.
Project notes (prints on PDF & Excel)
Result compare (A/B)
| Item | Pinned | Current | Change |
|---|---|---|---|
Saved rates auto-apply from your Price Library. Advanced details stay in your browser — nothing is uploaded except inside your own PDF/Excel exports.
Построить лестницу, соответствующую нормам, требует больше, чем догадки. Наш калькулятор выполняет расчёты. Введите общий подъём и получите точные размеры за секунды. Подвал, терраса или коммерческая лестница - точные размеры являются основой. Теорема Пифагора определяет длину струн. Носок добавляет безопасность и эстетику. Понимание этих цифр экономит время и деньги.
📖 Как Пользоваться Калькулятором Лестниц
मापें
आयाम मापें。
📐 Формулы и Примеры Расчётов
Кол-во ступеней = Подъём / Макс. высота (округлить вверх). Фактическая высота = Подъём / Кол-во. Проступи = Кол-во - 1. Пролёт = Проступи × Глубина. Струна = √(Подъём² + Пролёт²). Угол = arctan(Подъём/Пролёт).
⚠️ Типичные Ошибки при Расчёте Лестниц
Забыть проступи = ступени - 1
✓ Верхняя ступень на уровне пола.
Игнорировать носок
✓ Носок выступает за кромку.
Номинальные размеры
✓ 2×12 на самом деле 1.5×11.25 дюйма.
Непоследовательное округление
✓ Все ступени должны быть равны.
Толщина пола
✓ Измерять от чистового пола.
💡 Профессиональные Советы
Купите струну на 12 дюймов длиннее
Используйте угольник с направляющими
Примерьте первую струну
Проверьте зазор < 4 дюйма
Нанесите средство защиты
Добавьте площадку каждые 12 футов
Подпишите каждую струну
❓ Калькулятор Лестниц — Частые Вопросы
IRC 7,75 дюймов максимум.
Минимум 10 дюймов.
Калькулятор для прямых лестниц.
Две для 36 дюймов.
30-38 градусов.
Минимум 6 футов 8 дюймов.
🏗️ Реальные Проекты Лестниц
Отделка подвала 105 дюймов. Лестница террасы 54 дюйма - 7 ступеней. Коммерческая 12 футов - 20 ступеней.
Наш калькулятор определяет точные подъём, пролёт, длину струн и угол.
✅Method, Sources & Review
Maintained by theBuildingCalc methods desk· Last reviewedSeptember 23, 2026. This calculator implements the standards and references below; every figure can be rechecked against the formulas and worked example on this page.
Results are estimates, not engineering advice. Verify against local codes and licensed professionals for structural, electrical, and gas work. See ourTerms. Spotted an error? Report it— corrections ship with the next review.